Rancang Bangun Mesin Pemotong Rumput Berbasis Sistem Kontrol

Mazwan Mazwan; Ari Kurniawan; Ahmad Fauzi Pohan; Kholis Gunawan

doi:10.55679/pistonjt.v11i1.132

Authors

Mazwan Mazwan Program Studi Teknik Mesin, Politeknik Jambi, Jambi 36361
Ari Kurniawan Program Studi Teknologi Rekayasa Pemeliharaan Alat Berat Politeknik Jambi
Ahmad Fauzi Pohan Program Studi Teknik Mesin, Politeknik Jambi, Jambi
Kholis Gunawan Program Studi Teknik Mesin, Politeknik Jambi, Jambi

DOI:

https://doi.org/10.55679/pistonjt.v11i1.132

Keywords:

Grass-Cutting Machine, Control System, Linear Actuator, Track, Cutting Mechanism

Abstract

Manual grass cutting still requires considerable labor and has a low level of efficiency. Therefore, a device is needed to improve the effectiveness and efficiency of the grass-cutting process. This study aims to design and test a grass-cutting machine based on a control system equipped with a blade drive mechanism and a track-based mobility system. The research method included mechanical design, system assembly, and performance testing of the device. Testing was carried out on several main components, namely the blade drive mechanism, the track tensioning system, and the safety of the track shoe under various terrain conditions. The test results showed that the blade drive mechanism worked properly, in which the blade could rotate optimally when the linear actuator piston stroke reached 60 mm. The testing of the track tensioning system indicated that a tensioning distance of 6 cm was the most stable condition, as the track did not detach from the sprocket during operation. In addition, testing of the track shoe on flat and inclined roads over a distance of 15 meters showed that the system was able to provide good movement stability and traction without causing damage to the track components. Overall, the designed grass-cutting machine was able to operate stably and has the potential to be used under various terrain conditions in the grass-cutting process.

Downloads

Download data is not yet available.

References

Dedi Irawan dan Endah Fitriani, “Rancang Robot Pemotong Rumput Otomatis Berbasis Arduino Uno Dengan Sistem Kendali Aplikasi Blynk,” J. Ampere, vol. 6, no. 2, hal. 65–74, 2021.

S. Darmanto, G. Hanif, Y. Suryana, dan J. A. F, “Modifikasi Mesin Potong Rumput Model Gendong untuk Pemotong Pelepah Sawit,” vol. 22, no. 4, hal. 242–245, 2020.

D. Rahmanda, A. Azis, dan Y. Irwansi, “Perancangan Penggerak Pada Robot Pemotong Rumput,” Elektrika, vol. 15, no. 2, hal. 105, 2023, doi: 10.26623/elektrika.v15i2.8017.

S. Une, S. Akuba, dan B. Liputo, “Rancang Bangun Mesin Penggembur Tanah Menggunakan Mesin Pemotong Rumput,” vol. 6, no. November 2021, hal. 52–56.

K. Leelakar dan S. Krishnaraj, “Design and Fabrication of Body Framing and Chassis Development of Electrical Vehicle ( ATV ) With Simulation Analysis Design and Fabrication of Body Framing and Chassis Development of Electrical Vehicle ( ATV ) With Simulation Analysis,” J. Phys. Conf. Ser., hal. 1–13, 2021, doi: 10.1088/1742-6596/1964/6/062095.

S. P. Sutisna, E. Sutoyo, dan D. N. Pariatiara, “Rancang Bangun Pisau Robot Pemotong Rumput,” AME (Aplikasi Mek. dan Energi) J. Ilm. Tek. Mesin, vol. 6, no. 1, hal. 18, 2020, doi: 10.32832/ame.v6i1.2817.

Y. Yusman, W. Mellyssa, S. Salahuddin, K. Mukhlisin, dan S. Mualla, “Rancang Bangun Robot Pemotong Rumput Secara Otomatis dengan Kontrol,” Junal Infomedia Tek. Inform. Multimed. Jar., vol. 8, no. 2, hal. 100–105, 2023.

I. S. Perdana dan M. P. N. Sirodz, “Rancang Bangun Sistem Roda Track Pada Kendaraan Penyemprot Hama Otomatis,” e-Proceeding FTI, hal. 1–13, 2021, [Daring]. Tersedia pada: https://eproceeding.itenas.ac.id/index.php/fti/article/view/693%0Ahttps://eproceeding.itenas.ac.id/index.php/fti/article/download/693/574

M. Idzani dan S. Ihsan, “Rancang Bangun Mesin Pemotong Rumput Berbahan Bakar Gas,” vol. 4, no. June, hal. 2016, 2016.

M. Mulyadi, D. Wahyudi, A. Hidayat, dan M. A. Chandra, “Modifikasi Mesin Pemotong Rumput Jadi Mesin Tempel,” hal. 24–32, 2022, [Daring]. Tersedia pada: http://repository.pnb.ac.id/id/eprint/3201

Sofian Efendi, Mijer, Aditia Warman, Sarlan, and Budiman Sudia, “Perancangan Mesin Pencacah Rumput Pakan Ternak Menggunakan Sistem Penggerak Motor Listrik ”, Piston-JT, vol. 9, no. 1, pp. 15–23, Jul. 2024.

N. Endriatno, L. O. A. Barata, and Salimin, “Analisis Kekuatan Rangka Mesin Pencacah Nilam dengan Menggunakan Metode Elemen Hingga”, Piston-JT, vol. 9, no. 2, pp. 56–64, Dec. 2024.

M. Mazwan, S. D. Utama, dan Y. Agussationo, “Rancang Bangun Mesin Pengaduk Adonan Roti,” TURBO, vol. 13, no. 2, hal. 447–456, 2024, doi: https://doi.org/10.24127/trb.v13i2.3745.